Pewnie i kompas, ale po tym zabiegu nawigacja działa.
Niestety nie działa. Postaram się jeszcze opisać problem. Wróciłem na stockowy rom 5.0.1, włączam nawigację googla i tak działa przez 5 km. Później cały czas szukała gps i raz na 5 minut odświeżyła się moja lokalizacja. Gdzieś wyczytałem że trzeba pogrzebać w /system/etc/gps.conf W ty pliku jest:
#Uncommenting these urls would only enable
#the power up auto injection and force injection(test case).
XTRA_SERVER_1= http://xtra1.gpsonextra.net/xtra2.bin
XTRA_SERVER_2= http://xtra2.gpsonextra.net/xtra2.bin
XTRA_SERVER_3= http://xtra3.gpsonextra.net/xtra2.bin
#Version check for XTRA
#DISABLE = 0
#AUTO = 1
#XTRA2 = 2
#XTRA3 = 3
XTRA_VERSION_CHECK=0
# Error Estimate
# _SET = 1
# _CLEAR = 0
ERR_ESTIMATE=0
#Test
NTP_SERVER=time.gpsonextra.net
#Asia
# NTP_SERVER=asia.pool.ntp.org
#Europe
# NTP_SERVER=europe.pool.ntp.org
#North America
# NTP_SERVER=north-america.pool.ntp.org
# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
# 4 - Debug, 5 - Verbose
# If DEBUG_LEVEL is commented, Android's logging levels will be
used
DEBUG_LEVEL = 4
# Intermediate position report, 1=enable, 0=disable
INTERMEDIATE_POS=0
# Below bit mask configures how GPS functionalities
# should be locked when user turns off GPS on Settings
# Set bit 0x1 if MO GPS functionalities are to be locked
# Set bit 0x2 if NI GPS functionalities are to be locked
# default - non is locked for backward compatibility
#GPS_LOCK = 0
# supl version 1.0
SUPL_VER=0x10000
# Emergency SUPL, 1=enable, 0=disable
SUPL_ES=0 # Sensor R&D : Non-SUPL ES should be default
#Choose PDN for Emergency SUPL
#1 - Use emergency PDN
#0 - Use regular SUPL PDN for Emergency SUPL
USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=1
#SUPL_MODE is a bit mask set in config.xml per carrier by default.
#If it is uncommented here, this value will over write the value from
#config.xml.
#MSA=0X1
#MSB=0X2
#SUPL_MODE=
# GPS Capabilities bit mask
# SCHEDULING = 0x01
# MSB = 0x02
# MSA = 0x04
# ON_DEMAND_TIME = 0x10
# GEOFENCE = 0x20
# default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING |
GEOFENCE
CAPABILITIES=0x37
# Accuracy threshold for intermediate positions
# less accurate positions are ignored, 0 for passing all positions
# ACCURACY_THRES=5000
################################
#
#### AGPS server settings ####
#
################################
#
FOR SUPL SUPPORT, set the following
# SUPL_HOST=supl.host.com or IP
# SUPL_PORT=1234
# FOR C2K PDE SUPPORT, set the following
# C2K_HOST=c2k.pde.com or IP
# C2K_PORT=1234
# Bitmask of slots that are available
# for write/install to, where 1s indicate writable,
# and the default value is 0 where no slots
# are writable. For example, AGPS_CERT_WRITABLE_MASK
# of b1000001010 makes 3 slots available
# and the remaining 7 slots unwritable.
#AGPS_CERT_WRITABLE_MASK=0
####################################
# LTE Positioning Profile Settings
####################################
# 0: Enable RRLP on LTE(Default)
# 1: Enable LPP_User_Plane on LTE
# 2: Enable LPP_Control_Plane
# 3: Enable both LPP_User_Plane and LPP_Control_Plane
LPP_PROFILE = 0
################################
# EXTRA SETTINGS
################################
# NMEA provider (1=Modem Processor, 0=Application Processor)
NMEA_PROVIDER=1
# Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE)
SGLTE_TARGET=0
#################################################
#
# Select Positioning Protocol on A-GLONASS system
#################################################
#
# 0x1: RRC CPlane
# 0x2: RRLP UPlane
# 0x4: LLP Uplane
A_GLONASS_POS_PROTOCOL_SELECT = 0
Mógłby ktoś porównać ze swoim plikiem? Wracając jeszcze do tematu mapy Here tak samo jak Google raz na 5 minut zmieni się lokalizacja i cały czas szuka GPS. W GPS test takie rzeczy: